minicom:6818开发板串口的Ubuntu界面配置

  • 作者:zccc
  • 来源:网络
  • 2020-09-22 12:03:31

系统运维 通信:串行, 并行, COM串口, 485总线,can总线, 单总线 Open打开设备 配置设备 tcsetatttr, tcgetattr Write, read 写/读数据 关闭...

系统运维

通信:串行, 并行, COM串口, 485总线,can总线, 单总线

Open打开设备 配置设备 tcsetatttr, tcgetattr Write, read 写/读数据 关闭close

一.虚拟机串行端口设置:
1.关闭Ubuntu
2.接好6818开发板串口
3.打开:编辑虚拟机设置

4.点击下方:添加

5.点击: 串行端口

6.点击:完成
7.OK

8.开启Ubuntu

二.Linux下minicom配置

1.安装 :sudo apt-get install minicom

sudo minicom ctrl+A ----> O ----> Serial port setup gec@ubuntu:~$ sudo minicom -s
+-----[configuration]------+
Filenames and paths
File transfer protocols
------>>>> Serial port setup
Modem and dialing
Screen and keyboard
Save setup as dfl
Save setup as..
Exit
Exit from Minicom
+--------------------------+
串行设置
+-----------------------------------------------------------------------+
A - Serial Device : /dev/ttyS2
B - Lockfile Location : /var/lock
C - Callin Program :
D - Callout Program :
E - Bps/Par/Bits : 115200 8N1
F - Hardware Flow Control : No
G - Software Flow Control : No Change which setting?

+-----------------------------------------------------------------------+

回车

保存 -----> Save setup as dfl

    +-----[configuration]------+                                     
    | Filenames and paths      |                                     
    | File transfer protocols  |                                     
    | Serial port setup        |                                     
    | Modem and dialing        |                                     
    | Screen and keyboard      |
  ---> >>>> | Save setup as dfl        |
    | Save setup as..          |
    | Exit                     |
    | Exit from Minicom        |
    +--------------------------+
回车 ------------>>>> Exit from Minicom sudo minicom ----->>> 回车 (若光标下移,则成功,否则改Serial Device : /dev/ttyS2,还不行就一直往上加)

Minicom发送文件

进入minicom终端 : sudo minicom
Welcome to minicom 2.5

OPTIONS: I18n
Compiled on May 2 2011, 00:39:27.
Port /dev/ttyS2

Press CTRL-A Z for help on special keys

[root@GEC6818 /]#AT S7=45 S0=0 L1 V1 X4 &c1 E1 Q0
-/bin/sh: c1: not found
-/bin/sh: AT: not found[root@GEC6818 /]#

[1]+ Done(127) AT S7=45 S0=0 L1 V1 X4
[root@GEC6818 /]#
[root@GEC6818 /]#
root@GEC6818 /]#rx write_serial 回车

输入完后按ctrl+a +s

<a href=http://www.xinnet.com target=_blank>新网</a><a href=http://www.xinnet.com target=_blank>虚拟主机</a>

  • 相关专题

免责声明:本文内容由互联网用户自发贡献自行上传,本网站不拥有所有权,也不承认相关法律责任。如果您发现本社区中有涉嫌抄袭的内容,请发送邮件至:operations@xinnet.com进行举报,并提供相关证据,一经查实,本站将立刻删除涉嫌侵权内容。

相关文章

免费咨询获取折扣